Are you tired of dealing with a clogged and dirty Bissell Cleanview vacuum cleaner? Do you struggle to get the same level of cleanliness from your floors as you used to? It’s time to give your trusty cleaning companion some TLC! Cleaning the inside of your Bissell Cleanview is an essential part of maintenance that will help extend its lifespan, improve its performance, and leave your floors sparkling clean. In this comprehensive guide, we’ll walk you through the process of deep cleaning the inside of your Bissell Cleanview, so you can get back to tackling dirt and dust with ease.
Why Cleaning the Inside of Your Bissell Cleanview Matters
Before we dive into the nitty-gritty of cleaning the inside of your Bissell Cleanview, let’s talk about why it’s so important. A dirty interior can lead to:
- Reduced Suction Power: When the internal components of your vacuum cleaner are clogged with dirt and debris, it can significantly reduce the suction power, making it harder to pick up dirt and dust.
- Poor Airflow: A dirty interior can also restrict airflow, which can cause your vacuum to overheat, leading to premature wear and tear.
- Bad Odors: A buildup of dirt, dust, and dander can create unpleasant odors that can be difficult to eliminate.
- Increased Risk of Breakdowns: Failing to clean the inside of your vacuum can lead to mechanical issues, such as broken belts, damaged motors, and clogged pre-filters.
By regularly cleaning the inside of your Bissell Cleanview, you can prevent these issues and ensure your vacuum continues to perform at its best.
What You’ll Need to Get Started
Before you begin the cleaning process, make sure you have the following supplies:
- A screwdriver (preferably a Phillips head screwdriver)
- A soft-bristled brush or a small vacuum cleaner (optional)
- A cloth or paper towels
- Mild soap and warm water
- A clean, dry towel for drying
- The user manual (in case you need to refer to specific instructions)
Step 1: Disassemble the Vacuum
The first step in cleaning the inside of your Bissell Cleanview is to disassemble it. This will give you access to the internal components that need attention. Here’s how to do it:
- Remove the dirt tank and empty it.
- Take out the HEPA filter and set it aside for cleaning later.
- Remove the screw that holds the pre-filter in place and take out the pre-filter.
- Remove the screw that holds the brush roll in place and take out the brush roll.
- Remove the screws that hold the vacuum’s housing together and gently pry it open.
Step 2: Clean the Pre-Filter and HEPA Filter
The pre-filter and HEPA filter play a crucial role in capturing dirt, dust, and allergens. Here’s how to clean them:
- Pre-Filter: Tap the pre-filter gently to remove any loose dirt and debris. Then, wash it with mild soap and warm water. Let it air dry before reinstalling it.
- HEPA Filter: Tap the HEPA filter gently to remove any loose dirt and debris. Then, wash it with mild soap and warm water. Let it air dry for at least 24 hours before reinstalling it.
Step 3: Clean the Brush Roll
The brush roll is responsible for picking up dirt and debris from your floors. Here’s how to clean it:
- Remove Hair and Debris: Use a screwdriver to remove any tangled hair and debris from the brush roll.
- Clean with Soap and Water: Wash the brush roll with mild soap and warm water. Let it air dry before reinstalling it.
Step 4: Clean the Vacuum’s Housing and Internal Components
Now it’s time to clean the vacuum’s housing and internal components. Here’s how to do it:
- Use a Soft-Bristled Brush: Use a soft-bristled brush or a small vacuum cleaner to remove any dirt and debris from the internal components.
- Wipe Down with a Cloth: Use a cloth or paper towels to wipe down the vacuum’s housing and internal components. Make sure to remove any dirt, dust, or debris.
- Use Mild Soap and Water: If there are any stubborn stains or dirt buildup, use mild soap and warm water to clean the area. Make sure to dry it thoroughly before reinstalling the components.
Step 5: Reassemble the Vacuum
Once you’ve finished cleaning the internal components, it’s time to reassemble the vacuum. Here’s how to do it:
- Reinstall the Brush Roll: Put the brush roll back in place and secure it with the screw.
- Reinstall the Pre-Filter: Put the pre-filter back in place and secure it with the screw.
- Reinstall the HEPA Filter: Put the HEPA filter back in place.
- Reassemble the Vacuum’s Housing: Put the vacuum’s housing back together and secure it with the screws.
- Reattach the Dirt Tank: Put the dirt tank back in place.
Tips and Tricks for Maintaining Your Bissell Cleanview
To keep your Bissell Cleanview in top condition, here are some tips and tricks to keep in mind:
- Regularly Clean the Pre-Filter: Clean the pre-filter every 1-2 months to ensure optimal performance.
- Check and Clean the HEPA Filter: Check the HEPA filter every 6-12 months and clean it as needed.
- Empty the Dirt Tank Regularly: Empty the dirt tank after every use to prevent dirt and debris from building up.
- Store the Vacuum Properly: Store the vacuum in a dry, clean area to prevent moisture buildup.
Conclusion
Cleaning the inside of your Bissell Cleanview may seem like a daunting task, but with these steps, you’ll be able to give your vacuum the TLC it needs to perform at its best. Remember to regularly clean the pre-filter and HEPA filter, check and clean the brush roll, and reassemble the vacuum correctly to ensure optimal performance. By following these steps, you’ll be able to enjoy a cleaner, healthier home for years to come.
How do I access the inside of my Bissell Cleanview?
To access the inside of your Bissell Cleanview, start by unplugging the vacuum and turning it over. Locate the screws that hold the bottom plate in place and remove them using a screwdriver. Gently pull the plate away from the vacuum to access the interior. Be careful not to touch any of the electrical components or wires inside the vacuum.
Once you have access to the inside of the vacuum, you’ll be able to see the dirt and debris that has accumulated. You may be surprised at how much dirt and dust has built up inside your vacuum, even if you’ve been regularly emptying the dustbin. Take a moment to inspect the inside of the vacuum and identify any areas that need special attention.
What cleaning tools do I need to clean the inside of my Bissell Cleanview?
To clean the inside of your Bissell Cleanview, you’ll need a few basic cleaning tools. You’ll need a soft-bristled brush, such as an old toothbrush, to gently sweep away dirt and debris from the internal components. You’ll also need a damp cloth to wipe down the surfaces and remove any dirt or grime that has built up.
Additionally, you may want to use a gentle cleaning solution, such as a mixture of equal parts water and white vinegar, to help loosen any tough dirt or grime. Be sure to avoid using harsh chemicals or abrasive cleaners, as these can damage the internal components of your vacuum.
How do I clean the pre-filter and filter of my Bissell Cleanview?
To clean the pre-filter and filter of your Bissell Cleanview, start by removing them from the vacuum. Gently tap the filters against a trash can or other surface to remove any loose dirt and debris. Then, use a soft-bristled brush to gently sweep away any remaining dirt or dust.
For more thorough cleaning, you can wash the filters with warm soapy water. Be sure to rinse them thoroughly and allow them to air dry before reinstalling them in your vacuum. It’s also a good idea to replace the filters every 6-12 months or as recommended by the manufacturer.
How do I clean the suction path and vents of my Bissell Cleanview?
To clean the suction path and vents of your Bissell Cleanview, use a soft-bristled brush to gently sweep away any dirt or debris that has accumulated. You can also use a can of compressed air to blow out any dirt or dust that has built up in the vents or suction path.
Be sure to clean the suction path and vents regularly to ensure that your vacuum continues to perform at its best. A clogged suction path or vents can reduce the suction power of your vacuum, making it less effective at cleaning your floors.
How often should I clean the inside of my Bissell Cleanview?
It’s a good idea to clean the inside of your Bissell Cleanview every 3-6 months, depending on how frequently you use the vacuum. If you use your vacuum daily, you may need to clean it more frequently to keep it running at its best.
Regular cleaning can help extend the life of your vacuum and improve its performance. It can also help reduce the risk of the vacuum breaking down or needing expensive repairs.
What are some common signs that it’s time to clean the inside of my Bissell Cleanview?
There are several common signs that it’s time to clean the inside of your Bissell Cleanview. If you notice a decrease in suction power or if the vacuum is making strange noises, it may be due to a buildup of dirt and debris inside the vacuum. You may also notice that the vacuum is producing a lot of dust or dirt when you’re using it, or that it’s overheating.
If you notice any of these signs, it’s a good idea to clean the inside of your vacuum as soon as possible. Regular cleaning can help prevent these problems and keep your vacuum running smoothly.
Can I use a vacuum to clean the inside of my Bissell Cleanview?
It may seem counterintuitive, but you should not use a vacuum to clean the inside of your Bissell Cleanview. The internal components of the vacuum are delicate and can be damaged by the force of the suction or the brushes of another vacuum.
Instead, use a soft-bristled brush and gentle cleaning solutions to clean the inside of your vacuum. This will help prevent damage to the internal components and ensure that your vacuum continues to function properly.